Site last updated: Friday, November 20, 2026

Log In

Reset Password
Butler County's great daily newspaper

Jet drives help anglers reach shallows

I shut down the jet-drive outboard a bit upriver of the rocky bank I intended to fish. Dropping the bow-mounted trolling motor in, I set it so its thrust slowed the boat's drift.

The boulders that lined the bank broke the river's current and provided a perfect feeding lie for a hungry smallmouth bass. Picking up a rod rigged with a soft-plastic jerkbait, I fired a cast that landed a couple of inches from the shore. The bait drifted a few inches, then it was nabbed by a 2-pound river smallie.

Moments before my partner, Sid Brown, and I began fishing this spot, we had been skimming across a shallow riffle less than a foot deep. I never would have been able to access that rocky bank had it not been for the shallow draft of the 16-foot Roughneck boat and the clearance provided by the Evinrude E-Tec jet-drive outboard.

Jet-drive river boats open up a world of fishing opportunities for species like smallmouth bass that live in shallow rivers.

These motors rely on a jet of water for propulsion, rather than the thrust provided by a standard propeller. An intake that hangs just below the hull of the boat draws water in. A pump, driven by the engine, creates a high velocity jet stream, providing the thrust to propel the boat.

Though a few midrange outboards come from the factory set up as jet drives, it's more common to have the dealer convert a conventional outboard to a jet. When set up correctly with a shallow draft boat, a jet-drive rig is capable of navigating in inches of water.

Kneal Wiegel of Franklin has been rigging jet-drive boats for many years. He said the first consideration is to find the correct hull design and construction.

"I suggest anglers choose an all-welded hull," said Wiegel. "It should be made of a thick aluminum."

Flat-bottomed johnboats require little water to float and are used in many river situations, but Wiegel said it's best to have a bit of "V" designed into the hull.

"I prefer to have at least a seven degree V built into the shape of the hull," said Wiegel. "The boat handles better that way. ... It also handles rough water better."

Jet drives allow you to access water that is off limits to conventional prop drives, but it does come at a price. First, there is a 30-percent reduction in horsepower.

For instance, a 60-hp outboard set up with a jet develops about 40 horsepower.

Jet drives also are less efficient than prop drives, so they use more fuel, which, with the rising cost of fuel, is something that needs to be considered.

What is the minimum depth anglers can expect to run in with a jet?

"I tell folks to expect to run in about eight inches of water," Weigel said. "A lot a variables come into play. How the motor is set on the transom, the weight distribution in the boat, the river bottom, which is mostly gravel and sand in the shallow riffles of the rivers in Western Pennsylvania, is not even. Eight inches is a fairly safe estimate of what you can run in, given the variables."

The height of the outboard on the transom is a big factor as well.

In his many years of rigging these boats, Weigel said he has found that there is a sweet spot. If you are off by a quarter of an inch one way or the other, that discrepancy can affect how the boat runs.

If it's too high, the pump will be starved for water and will cause cavitation. If it's too low, you lose the clearance you need to run in shallow water. Keels and rivets on the bottom of the hull also affect how "cleanly" the water flows into the jet's intake.

"Weight distribution is also an important factor in how a jet boat will perform," Wiegel said. "Some folks come back and tell me that they put all the extra weight, fuel tanks, batteries and such up front. Most times that is a mistake. You want some of the weight in the back.

"When the boat is on plane, it should be riding on the back pad of the hull. That means the plume of water spraying from the hull should start about two-thirds of the way back from the bow," he added.

Kneal suggests a two-stroke outboard over a four-stroke. Four-strokes weigh more and don't offer the torque that a two-stroke does.

It takes some time to become accustomed to the handling characteristics of a jet-drive outboard. Since the jet doesn't "screw" through the water like a prop, it doesn't have the same bite. Hence, they are a bit more difficult to control.

You don't notice it that much when under full power, but it becomes apparent during low-power maneuvers, such as driving the boat on the trailer, how tough it is to keep it in line.

More in Sports

Subscribe to our Daily Newsletter

* indicates required
TODAY'S PHOTOS