Weed control necessary when targeting muskies
In his muskie fishing classic "Man Against Musky," author Howard Levy describes his meeting with Dewey Baldensperger, who was the guru of muskie fishing on New York's Chautauqua Lake at the time.
"You sure don't know much about fishing," were Baldensperger's first remarks to Levy when the author cornered the renowned angler one day after both had put in a shift on the water.
Levy had watched Baldensperger land several muskies while his own boat had experienced no action. Baldensperger went on to comment that in the hour he had watched Levy troll the water behind him, he never saw him lift his plugs from the water to see if they had "a slight wisp of weeds on them."
Indeed, the difference between a successful day of trolling and one where you merely take you plugs for a ride often is the ability to keep them clean. Levy's book was published in the early 1960s. Anglers have been struggling with the problem for many years.
By late summer, the surface of many bodies of water features a covering of floating weeds, which often are cut free by anglers working the shallows.
Boats and jet skiers rip through the shallows during the summer, creating a flotilla that is often driven by the wind to the open water basins muskie trollers commonly fish. The arrival of fall adds a covering of floating leaves to the mix.
The debris isn't limited to the surface, either, as suspended weeds and leaves hang in the water column, just waiting for the chance to wrap around your line and run down to your plug, fouling its action and otherwise presenting a dirty lure muskies will ignore.
Frustrated by trolling great- looking water that is teaming with schools of baitfish, only to find that one or more lures had picked up a weed, I developed a multi-component game plan to be sure my lures spend as much "clean" time as possible. Though geared toward the muskie fisher, many aspects apply to trolling in general.
n
Rod tips in the water. Typically, the first line of defense against picking up floating weeds and leaves is the act of rigging rods so the tips are submerged below the surface of the water. The tip-top and first guide or two act as "catchers" to snag debris before it can wrap around your line and work its way down to your lure.Naturally, to do this your boat needs to be rigged with rod holders. Rod holders come in a variety of configurations. For this type of work, the primary requirements are that they be strong and that they have a good degree of adjustment.The strength factor comes in to play regardless of whether floating debris is an issue or not. Muskie crankbaits, deep divers in particular, put a significant strain on equipment, rod holders included. The thumping of high-action lures can cause wimpy rod holders to jump out of their bases.Adjustability is important in that you want to position the rod so that just the tip-top and first guide or two are in the water when the boat is in its trolling attitude. Placing too little of the rod in the water means you might well pick up weeds when that side of the boat bounces up from wave action. Too much in the water places undue strain on the rod.As a rod picks up debris, it's important to clear it as soon as possible. Leaving weeds hang on the rod tip is inviting the opportunity for some of them to work their way down your line. Also, a heavy build up of weeds will produce a great deal of drag. This could translate in to a broken or cracked tip section of a trolling rod. The action of lifting a fouled rod from the holder and sharply shaking the tip is usually enough to clear it.The disadvantage of positioning rod tips below the surface is that you cannot "read" the action of the rod tip to determine if a lure has been fouled.n
Clamp a release to the line. Though they are used little in muskie fishing, walleye anglers often apply the use of inline snap weights in their open water trolling schemes. Last summer, while fishing by myself on some particularly weed-covered waters, I experimented with using a component of the snap weight system to help keep my trolled lures clean.Snap weights employ a clip to attach the weight to the line. I removed the clip from the split ring that coupled it to the lead weight. I then let out a trolled plug and placed the clip about 20 feet behind the rod tip. This put the clip about a foot under the surface.The snap-weight clip did a great job of catching surface debris. I'd say that about 90 percent of the time that I brought in a lure to check it, the lure was be weed-free.The clips I used were Offshore Tackle's OR-16 Snap Weight Clip. Two pinch pads on the clip hold it to the line. It's a good idea when using slippery braided superlines, which are commonly used in trolling applications, to run a loop around the clip when attaching it to the line.Keep in mind that the clip will need to be removed from the line before you can land a fish. This is not such a big deal if you have a boat partner. Have him or her pop the clip off while you maintain pressure on the fish.If you are by yourself, point the rod behind you as the clip nears. The bend in the rod will lower the clip to a position where you can reach up and remove it, and the bend also will maintain pressure on the fish.n
Extra-long leaders. Despite your best efforts, some weeds and leaves are going to work their way down your line. Some debris is suspended in the water column, placing it below precautions incorporated at the surface.Junk that makes its way down your line often will hang up on the swivel of your leader. Recently, I began tying leaders in the 6- to 7-foot range, so that any debris caught on the swivel is a fair distance away from the lure. This is about as long a leader as you can get away with and still be able to get a muskie in netting range at the boat.The long leaders also provide a level of protection for a muskie that is rolling in the line. The thicker leader material is easier on the fish.I tie my leaders from 60-pound test Seaguar Fluorocarbon leader material. Snaps are 200-pound-test and swivels are 150-pound-test. Both are from Bait Rigs.Bulletproof Tackle provides a unique feature in the trolling leaders it markets. A weed catcher is incorporated in the connection of leader and swivel. The tag end of the knot is left extra long and is pointed at an angler likely to capture weeds. The stiffness of the fluorocarbon makes this feature effective.n
Periodic checks. The best insurance that your lures are running clear is to check them on a frequent basis. While long lines are sometimes incorporated in muskie trolling, most times the let out is 75 feet or less, many times much less. It only takes a minute or two to crank in a bait to be sure it's running clean. Yes, it is time the lure is out of the water, but it's a gamble I'm willing to take when compared to the chance of pulling around a dirty lure for an extended period of time. Rod tip action will reveal a heavily fouled lure, but it won't divulge the presence of a wisp of a weed on a hard working muskie crankbait.I keep the time of day displayed on my sonar device. Every 15 minutes I crank in the lines to check them. If it appears I can stretch the length to 30 minutes, I will do so.
